Top Five Types of Revolver Grips

Editor’s Note: The following is a post by Mark Kakkuri, a nationally published freelance writer who covers guns and gear, 2nd Amendment issues and the outdoors. His writing and photography have appeared in many firearms-related publications, including the USCCA’s Concealed Carry Magazine. You can follow him on Twitter @markkakkuri.

Read Mark’s previous articles in this “Top Five” series:

I’ve been on a bit of a revolver kick lately, and this week I can’t get away from the topic. In fact, my main concealed carry gun (for now) is a Ruger LCR with five .38 Special +P rounds on board and six additional rounds in a Bianchi Speed Strip. But other revolvers might get called up for review duty as well, including an Airweight S&W J-frame or an UltraLite Taurus. Revolvers have their pros and cons, of course, but in the pro column are the unique aftermarket accessories available for changing up the grips or stocks. Here are my top five types of revolver grips.

1. DeSantis Clip Grip

I don’t condone carrying a revolver (or any gun, for that matter) in any manner that doesn’t fully cover the trigger. So, this DeSantis Clip Grip makes for a bit of a conundrum. With a plastic clip pointing forward from one side of the grip, this enables the user to tuck the revolver inside a waistband — the clip catching the top of the belt — and just go. So, the trigger is sort of covered because it is tucked inside a waistband, but not really.

Anyway, I’ll admit I’ve used one and — safety issues aside — it is a very handy means of concealed carry. Easy in, easy out, and relatively secure as long as your belt is pulled decently tight. So, how does it make the top five? Because with a wide enough belt, it is possible to carry it in a manner that adequately covers the trigger the same way a holster would.

Visit the DeSaints website to learn more.

2. HySkore Grip Light

Here’s a grip replacement that provides an over-molded plastic and rubber grip system with an integrated flashlight operated by a front-strap-mounted on/off switch. Grip the gun and a nice flood of light fills up the area in front of you, allowing you to see your target.

When the grip is installed, the integrated flashlight ends up to the upper right rear of the cylinder, close to the gun so you can still holster it but out of the way of the gun’s sights. The light is a CREE LED diode (100 lumens) and is powered by an on-board battery. There’s a separate on/off switch under the grip for when the gun is not in use. But when the switch is turned on, simply grasping the gun will depress the activation switch, turning on the light.

The HySkore Grip Light adds length to the gun’s grip, which might reduce concealability. But it certainly improves your ability to see your target. If you have a revolver for a house or car gun, this might be a great addition.

Visit the Hyskore website to learn more.

3. Crimson Trace Lasergrips

Lasers are fast becoming a ubiquitous handgun accessory, allowing a user to put a red or green laser beam directly on the point of aim simply by grasping the gun.

Crimson Trace, a major handgun laser manufacturer, makes its Lasergrips for dozens of handgun makes and models, including revolvers. Similar to the operation of the HySkore Grip Light, a Crimson Trace Lasergrip turns on via a front-strap-mounted switch that’s depressed when you grasp the gun. The laser beam emits from the right side of the grip panel, just above the area where a user’s right hand contacts the gun. As such, you have to be careful not to raise your right finger too high when you rest it on the side of the gun lest you block the beam.

A little practice eliminates this problem and the laser’s strengths become immediately clear, especially in incidents where you have to draw and shoot very quickly, often without acquiring a normal sight picture. But the laser shows where the gun is aimed as you’re holding it. It’s a great system and, like all gun functionality, requires practice in order to master.

Visit the Crimson Trace website to learn more.

4. Hogue Hardwood Grip

Sometimes a grip change on a revolver is almost entirely aesthetic. Hogue Hardwood Grips, for example, offer decent purchase and certainly allow clothing to drape easily over them. So there’s some functionality. But they look absolutely fantastic. So if you’re into dressing up your revolver, this is one way to do it.

Some grips might offer finger grooves, which increase purchase, too, but generally, hardwood grips are known for looking good (and, unfortunately, allowing recoil to be transferred directly into the web of your hand.) So, if you’re shooting .38 Special and greater calibers, don’t plan on shooting too many of them with your hardwoods installed.

Visit the Hogue website to learn more!

5. Hogue Tamer Grip

At the beginning, I mentioned the Ruger LCR I’m currently carrying, and part of the reason I enjoy carrying the LCR so much is because it ships with the Hogue Tamer grip.

This rubber grip has a terrific textured surface, finger grooves and a softened pad right where the gun contacts the web of my hand. It’s a fantastic combination of features that, along with the other grips mentioned here, will get you thinking about carrying a revolver for self-defense.

Visit the Hogue website to learn more!

  (https://www.gunsamerica.com/blog/top-five-types-revolver-grips/